*** M1 Garand PARTS LIST ***
Beretta M1 Garand Rifle $1,995
7.62 cal. unique spacer in magazine well to accomodate 7.62 cartridges. The
length of the rifle is less than a half inch shorter than the U.S. M1 Garand.
Receiver is stamped P. Beretta
Made in Italy
low serial numbers
The parts for the Beretta Garand are intechangable with the U.S. Garand except
for the barrel, op rod, rear handguard, and the
stock.
Just what you need to finish your Garand Collection
Berretta Garand Barrels New Condition .308 - $200.00 (8 left)
M1 Garand Firing Pin - Excellent Condition - USGI - $19.95 (SOLD OUT)
rear-swivel-$5.00
Quick detach muzzle break adapted to fit U.S. M1 Garand.-$120.00
M1 Garand Hammer- Excellent condition. (SOLD OUT)
Tricompensator-muzzle break-flash hider..Modified to fit M1 Garand $59.00
The picture of the tricomensator you see above has been modified to fit the M1 Garand All ready to fit on your Garand..just take off the gas cylinder lock....screw on the tricompensator screw in gas cylinder plug and you have a pussy cat. Turns the Garand into a cream puff! Tricompensator, also works as a grenade launcher. Fits all BM59's (except E Model). Fits Beretta standard bayonet. Approx. 7" long. Fits BM 62 - BM 59 - BM 69 $59.00
Stacking Swivel and Screw - for making the M1 Garand perfectly complete! Only $9.95
Hardware for M1 Garand front and rear handguards - 3 pieces - $12.00
Trigger guard milled -$20.00 Trigger guard...stamped.. - $14.95
Barrel - Beretta - 7.62 - NEW - 1/2" shorter than 30.06 G.I. barrel - $275 Brand New Bullet Guide - Still in the original packaging and greased
Stamped Bullet Guide - $6.95 Clip Latch - Sold Out
M1 Garand Latch Springs -$1.00
Clip Latch Pin - NEW - $2.00 per pin
Firing Pin - G.I. $14.95
Follower Arm - $6.50 Follower Arm Pin - $2.00 (Sold Out)
Follower Assembly - $9.50 (Sold Out) Follower rod - new- G.I. $3.95
For the collector - original package of 20 follower rods manufactured from Springfield Armory - packaged Front Handguard Ferrule, Spacer, and rear handguard clip - $12.00 Front sight - $12.00 (Sold Out)
Front sight screw - $1.50
Gas Cylinder Lock without Hump, Early style - $8.95 Beretta Gas Cylinder Lock Plug -Solid-New- $7.50 Gas Cylinder complete with stacking swivel - .G.I.- guages good - has a cross
cut..so that it will tighten on the barrel better $45.00 (Sold
Out)
Rear Handguard retaining clip - $4.00
Rear Sight Aperature Early Model lightly checkered to stop glare Rear Sight Base - $12.50 (Sold Out) Trigger Group, complete with milled trigger guard - $110 (Sold
Out)
Trigger Housing - G.I. - used..very good condition - Combo Tool with Chamber Brush G.I. - $14.95 (Sold
Out)
M10 Teardown tool - $14.95
All you need to tear down and maintain your M1 Garand
M1 Garand Tear Down Tool.....Excellent condition...$14.95 ea. (SOLD OUT)
****************************************************************************
This is the 5 inch BM69 Muzzle Break modified to fit right on
a M1 Garand. $59.00
Lock Bar
$15.00 Square Corner
$20.00 Round Corner
this is the model with the notch - $10.00
Garand Bullet Guide Milled/Forged - $10.00
Oct. 5, 1953, package of 20 - $50.00
with matte finish - $15.00
SA - $25.00
WIN - $20.00 (Slightly pitted)
PB - $25.00
FEATURED ITEM - M1 GARAND BI-POD - made from
the legs of the very durable BM59 bi-pod. Nearly all aluminum, weighs 1/2 pound
and is adapted for the M1 Garand. Legs fold up parallel with the barrel. Attaches
in approx. 30 seconds. Replaces original gas cylinder lock. Gun can be tilted
45 degrees right or left. Does not interfer with front sling swivel. No modifications
needed. $69
